[[messageType]]
[[message]]
| Calculation Performed at www.codecalculation.com | |||||||||
[[ doc['meta']['docClass_title'] ]] |
|||||||||
Project |
|||||||||
| Project No: | |||||||||
| Project Title: | |||||||||
| Document No: | |||||||||
| Revision No: | |||||||||
| Date : | |||||||||
Inputs |
|||||||||
| Mass Flow Rate qm [[ gUL('massflow') ]] |
[[err]] |
||||||||
| Molecular Weight MW [[ gUL('molecularMass') ]] |
[[err]] |
||||||||
| Flowing Temperature T [[ gUL('temperature') ]] |
[[err]] |
||||||||
| Compressibility Factor Z |
[[err]] |
||||||||
| Heat of Combustion LHV [[ gUL('specificEnergy') ]] |
[[err]] |
||||||||
| Flare tip absolute pressure p2 [[ gUL('pressure') ]] |
[[err]] |
||||||||
| Design Wind Velocity U∞ [[ gUL('speed') ]] |
[[err]] |
||||||||
| Mach No Ma2 |
[[err]] |
||||||||
| Inside Diameter basis |
[[err]] |
||||||||
| Flare Inside Diameter d [[ gUL('length') ]] |
[[err]] |
||||||||
| Distance from Flare (@grade) R [[ gUL('length') ]] |
[[err]] |
||||||||
| Atmospheric Transmittivity 𝜏 |
[[err]] |
||||||||
| Radiative Heat Fraction F |
[[err]] |
||||||||
| Refer Table 13 of API RP 521 for Guidance on F values to be used above | |||||||||
| Maximum Allowable Radiation K [[ gUL('intensity') ]] |
[[err]] |
||||||||
| Refer Table 12 of API RP 521 for Guidance on K values to be used above | |||||||||
|
Errors |
|||||||||
|
[[ err ]] |
|||||||||
Results |
|||||||||
| Flare Diameter d [[ retSilent(doc, ['result', 'd', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Heat Liberated Q [[ retSilent(doc, ['result', 'Q', '_val']) ]] [[ gUL('power') ]] | |||||||||
| Flame Length L [[ retSilent(doc, ['result', 'L', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Flame Distortion | |||||||||
| Vapor Volume Flow Rate qvap [[ retSilent(doc, ['result', 'q_vap', '_val']) ]] [[ gUL('flow') ]] | |||||||||
| Flare Tip Exit Velocity Uj [[ retSilent(doc, ['result', 'Uj', '_val']) ]] [[ gUL('speed') ]] | |||||||||
| Parameter U∞/Uj [[ retSilent(doc, ['result', 'Uinf_by_Uj', '_val']) ]] | |||||||||
| Parameter Σ(Δy/L) [[ retSilent(doc, ['result', 'Sdy_by_L', '_val']) ]] | |||||||||
| Parameter Σ(Δx/L) [[ retSilent(doc, ['result', 'Sdx_by_L', '_val']) ]] | |||||||||
| Distances as per Figure C.1 of API RP 521 | |||||||||
| Distance ΣΔy [[ retSilent(doc, ['result', 'Sdy', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Distance ΣΔx [[ retSilent(doc, ['result', 'Sdx', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Distance D [[ retSilent(doc, ['result', 'D', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Distance R' [[ retSilent(doc, ['result', 'R_prime', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Distance H' [[ retSilent(doc, ['result', 'H_prime', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Flare Stack Height H [[ retSilent(doc, ['result', 'H', '_val']) ]] [[ gUL('length') ]] | |||||||||
| Calculation Performed at www.codecalculation.com | |||||||||
|
|||||||||